Dremel digilab 3d slicer software download11/23/2023 ![]() I could speculate about why the Dremel engineers are setting the print speeds of the profiles too high, but that’s not the point of this review. The only way the HQ print outshines the MQ print is that it has less layer stepping, which is hard to notice past its other faults. Here is the result:īy nearly every objective measure, the “Medium Quality” print is superior to the “High Quality” print. To demonstrate that claim, I increased the layer height to the Medium Quality 0.2mm/200 micron setting and lowered the print speed from 50 to 35 I also lowered the extrusion temperature from 220 to 218, decreased the flow rate from 100% to 99.5%, and increased the retraction distance from 2mm to 2.5mm. While it does increase Z resolution and surface appearance, there are several other print settings that need to be correctly configured in order to realize the quality improvements gained by using lower layer heights. It is a misconception that layer height is the primary driver of 3D print quality. Some stringing and the merging of the support pillars with the part indicate that the temperature might be a bit high, and some dotting told me that more retraction was needed. Beyond that, there are minor inconsistencies in the layers that I attribute to motion backlash and not enough cooling, both of which are easily addressed by slowing the print speeds. Supports weren’t needed for this print, but some of the print settings were causing the supports to merge with the print, making them impossible to fully remove. That’s certainly not the best the 3D40 Flex can do, though. And then after some difficulty removing most of the supports, this was the result:įor a first print, it’s pretty good some users would be pleased while others might feel a bit disappointed with what they believe is the best quality the machine can produce. After easily removing the bed from the machine and bending the plate slightly, the part popped right off. The default settings included supports, which are not necessary for the Benchy model. This was, by far, the fastest, easiest, most straightforward 3D printer setup I’ve personally experienced. From the unboxing to the beginning of the print, perhaps 15 minutes had past. To my amazement, the printer initiated its nine-point self-leveling process (it does this before every print and takes only a couple minutes) and then started printing. So I loaded up Benchy, a standard torture test, and sliced it with the standard High Quality (0.1mm/100 micron layers) profile without even looking at the parameters/settings and sent it to the printer. USB Flash Drive (with slicing software and a few 3D models)įor the first print, I wanted to simulate how a certain type of potential customer might use the printer: someone who has little-to-no 3D printing experience or knowledge but has high expectations.Why go three feet across my office when I can instantly send a 3D file through the air? What’s in the box The last step is optional as files can be moved to the printer via the included USB drive, but this is 2019. I then installed the included slicing software onto my computer and connected the printer to my wifi. For leveling, the touchscreen also guides users through the process, which involves turning each of the two knobs below the bed until it prompts to stop. ![]() The filament spool is loaded into the left side where the filament is fed through a guide tube before reaching the extruder the touchscreen prompts users when to insert the filament into the top of the extruder and it takes it from there. It comes FULLY assembled and the only steps to get going include loading the filament and leveling the bed. I’ve worked with paper printers that took longer to set up than this 3D printer. I was eager to get printing so I immediately got it into my office. I like the decision to use a ribbon cable on the extruder, and the flexible (where it gets its namesake), magnetic bed is a wonderfully convenient feature that’s well designed we’ll cover it more later. The blue tape was a bit cumbersome but not a big deal.Įverything seems well put together and sturdy. It’s rather light so it’s easy to lift out, and removing the inserts did not break them, which is especially relevant here as I’ll be returning this printer after the review. The 3D40 Flex is very well packaged as it’s entirely box-shaped, it comes with only a few custom inserts, mostly to hold everything in place within the build chamber. Packaging may seem trivial but it was a real problem in the early days of desktop 3D printers as many arrived damaged from poor packaging.
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |